Litter Robot 3 "open-air"
Bought one. Not sure about prior models, but it is okay. Doubt I
would have liked the preceding models' small openings. With the current model you can easily wipe off the inside, so you can remove the shield, giving them a little more room inside. Mine slightly bobs up and down as it cycles. I guess the gear or the motor shaft is out of alignment. But it works. Using Arm & Hammer Clump & Seal. Without having used the prior models, I suspect complaints about the waste bag holder are correct. But it probably can be modified. So far, it is fun, but will see how it does after many more months of use. Longevity is the question. |
Litter Robot 3 "open-air"
Toobig (the bully) sticks her front end into the Litter Robot
when it is cycling. It moves, therefore it must be conquered. I wrote: Bought one. Not sure about prior models, but it is okay. Doubt I would have liked the preceding models' small openings. With the current model you can easily wipe off the inside, so you can remove the shield, giving them a little more room inside. Mine slightly bobs up and down as it cycles. I guess the gear or the motor shaft is out of alignment. But it works. Using Arm & Hammer Clump & Seal. Without having used the prior models, I suspect complaints about the waste bag holder are correct. But it probably can be modified. So far, it is fun, but will see how it does after many more months of use. Longevity is the question. |
Litter Robot 3 "open-air"
Toobig stopped messing with it. All three are using the Litter
Robot Open Air with no problems. I have started using Arm & Hammer SLIDE litter. So, these are the modifications I have made to the litter ball... Removed the crud shield from inside. I figure it was just a strain on the motor. The opening of the newest litter ball is so large, you can easily wipe off the inside if you want to. No need for a shield taking up space inside. Also removed the shield guide. It is near the front along the top. Cut it out with a utility knife. It can be scored and then broken, or just cut through. Helps to mark the crease with a marker so that you know where to cut. That increased the space inside a little more. Completely disassembled the ball before starting the new litter. Must be VERY careful when taking the quad sections apart. Use a fluorescent marker to mark the magnet orientation. That is very important, or you will be messaging technical support for help. And they do not even know how the magnets go when it is reassembled. They person I messaged had a good idea, but they were not exactly right. Removed the weight from the rubber liner. It will hold a tiny bit more litter. I figure it does not need to buckle when cycling since using the SLIDE litter. In practice, that has proved more or less correct. The clumps eventually come unstuck if not immediately. The rubber liner could be completely removed I suppose. But if it isn't broke, don't fix it. So I will wait. Removed the crap foam from its various positions. Also removed the hairy tape along the bottom. That is not really recommended but it does get in the way when cleaning the thing and eventually it will fall off anyway. But some grease made specially for plastic (DOW MOLYKOTE EM- 30L). After cleaning the ball, applied a very tiny amount around the ball on certain paths. The location could probably be determined by using a marker across the ball and then see where the ink wears. Apparently I have it in the correct locations, it is spinning smoothly. Using ordinary plastic T-shirt grocery bags with the handles cut off. Won't go into the process for taping them to the litter drawer, but it works well. And it is dirt cheap. My opinion so far... Like it. I like plastic. I like automation. It does not do everything, but it does the hard work so you do not have to worry about it. Besides the introductory hassle that is always the case with something new... You might need to clean off the inside from time to time. But you do that at your leisure instead of (like) raking the litter box that must be done on a schedule. You must be familiar with plastic screws. Carefully reverse direction and listen/feel for the correct place before screwing the screw into the hole. Do not over tighten and do not worry about the really weird fact that the screen is actually unscrew themselves a tiny bit after you tighten them down. Never seen that happen before. Probably something to do with the type of plastic. |
All times are GMT +1. The time now is 09:43 AM. |
Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
CatBanter.com